The ice maker line to my ice box presently does not have any shutoff valve and I also’d choose to include one but i can not determine what size the connector is

we bought a 1/4 inches valve because the ice manufacturer connector we have actually says 1/4 FCM upon it nonetheless it didn’t fit. It appears a lot more like 1/8 inches, but a 1/8 inches valve does not fit either, though it is quite near. Where could I find details about water pipeline sizes, there should be some standard?

The copper water line i will be linking it to gets the precise measurement that is same the refrigerator.

MODIFY:

Okay we thought that looking the world-wide-web for 1/4″ OD Valve Male Female would get me the things I require but i’m getting no outcomes thus I’ve reopened issue! Can anybody offer me personally an internet connect to a item which will fit? I have added an image associated with the connection that is current i would ike to include the valve. Many Thanks!

3 Responses 3

You can find various criteria to pipelines and threads. Your problem is the fact that you want to mix two various standards that are threaded.

The ball valve which you connected to has nationwide pipeline threads (NPT). NPT are tapered plus it is the fact that taper that produces the seal from a male and female joint. No washers are expected.

What exactly is shown in your picture is compression fixtures which may have a right or operating thread. The seal is created by either a ferrule or a plastic washer.

Available for you, the text involving the copper pipe as well as the supply hose happens to be made the following:

1/4″ Copper Tube > 1/4″ Compression by 1/4″ Compression Coupling > 1/4″ Supply Hose

The seal on a ferrule makes the copper tube that is situated underneath the nut. Due to the fact nut is tightened, the ferrule is compressed between your coupling while the pipeline.

The seal on the supply hose part is created by way of a plastic washer that is often integral the the nut for the supply hose. (The compression coupling might have include two pea pea pea nuts, certainly one of which was discarded due to the fact supply hose has one integral.)

Therefore, to respond to your concern, you simply require a 1/4″ compression x 1/4″ compression valve that may change the present coupling. The following is a hyperlink to this type of valve.

Do the paperwork is had by you that was included with the refrigerator? It must show the ice maker install and say the size maybe associated with valve. I’ve constantly seen it to be 1/4″.

Where could be the water line tapped from? Often it comes down a 1/2″ copper pipeline. You can place your valve in the copper pipeline part.

EDIT: web Page 33 regarding the installation manual states that the water supply pipe is 1/4″ OD. You want a 1/4″ valve. Be certain there are not any burrs in the copper tubing after it is cut by you. Often you ought to register the sides. In the event that pipe cutter just isn’t razor- sharp it could mushroom the ends and that may ensure it is appear it is perhaps perhaps not the diameter that is right.

When you yourself have more hours and cash, the advisable thing is to run either a 1/2 inches copper line or even a 1/2 galvanized line towards the straight back of the fridge having a 1/4 inches connection about it, ideally set into the wall surface in synthetic field. An alternative cheaper means would be to run a 1/4 inches line through the 1/4 inches connection at your double shut off valve under your drain. But, the copper line is just a difficult line and it gets crimped specially when you or somebody else is careless in moving the refrigerator around to completely clean or any.

Utilizing two crescent wrenches, this is what to complete if you currently have a difficult copper line towards the straight straight straight back without a turn off valve anywhere in web web web site. You should buy a kit with the right parts you will need, 1/4 inches connectors having a 6 base, 1/4 inches supply hose, with the 1/4 pea pea pea nuts on both ends. Carefully take action your self or obtain a plumber to slice the copper line by having a copper pipeline cutter, a great cut that is clean a couple of ins this part of in which the line happens of wall surface or case (provided that it is not crimped, you are ok to cut it).

Place the free 1/4 inches nut on backwards regarding the pipeline, and so the nut covers the ferrel tucked in during the edge of the end for the pipeline, then, screw regarding the 1/4 inches connector/adjuster about it, utilizing the 1/4 inches threads into the 1/4 inches nut from the hose, and tighten, snug, never ever overbearing, ever with any plumbing system. Then connect one other end of hose/nut towards the end that is threaded the ice box at the end, snug! Keep In Mind! Nonetheless, a good thing doing whenever you are linking a line to either a tap or ice box or in any case are, just before put that final connection in the ice box, put that result in a big bucket and turn it in to clear the type of air and grub, because that knows the length of time it has been sitting. Plus, if you have atmosphere within the lines, that is a nother that mail order wife is whole, trust in me that you don’t desire! Obtain the fresh air away! You can certainly do all this your self too! Don’t neglect to always check every thing for leaks! Best of luck! Now get commemorate you merely spared your self $150.

Leave a Reply

Your email address will not be published. Required fields are marked *